Which of the following CV joint tests should be performed to determine if the CV joint needs to be s

Are you stressed by poor grades and tight deadlines? We have your back. We can do this or a different assignment for you at an affordable price. Use customdissertations.org writing services to score better and meet your deadlines.


Order a Similar Paper Order a Different Paper

Which of
the following CV joint tests should be performed to determine if the CV joint
needs to be serviced?

a.

balance test

b.

chassis test

c.

squeeze test

d.

spin test

__ 16. Which
double U-joint arrangement is often used in large cars with long drive shafts?

a.

Cleveland-style

b.

Detroit/Saginaw-style

c.

double Cardan-type

d.

Spicer-style

____ 17. Which
type of drive axle supports the weight of the vehicle?

a.

three-quarter floating

b.

semifloating

c.

full-floating

d.

independent

____ 18. Which
of the following describes the double Cardan universal joint?

a.

It has a centring ball socket inside the coupling
yoke between the two universal joints.

b.

It is constructed of a single cross piece mounted
between two balls

c.

It is not a constant velocity U-joint.

d.

It is often installed in front-wheel-drive luxury
automobiles.

____ 19. Which
type of U-joint uses an outside retainer ring that fits into a machined groove
in the yoke?

a.

Detroit

b.

Cleveland

c.

Spicer

d.

Mechanics

20. The final drive crown gear speed is 600 rpm
while the left rear wheel is turning at 400 rpm. What is the speed of the right
rear wheel?

a.

400 rpm

b.

200 rpm

c.

800 rpm

d.

1,200 rpm

____ 21. Which
of the following describes the hypoid gear ?

a.

The spur bevel crown and ring gears are used.

b.

The centre line of the pinion gear is below the ring
gear centre.

c.

The crown gear and the pinion gear centre lines are
on the same plane.

d.

A spiral helical crown and pinion gear set is used.

____ 22. Which
final drive component must rotate at the same speed as the ring gear?

a.

differential carrier

b.

drive pinion

c.

side gears

d.

differential case

____ 24. How
many bearings does an overhung mounted pinion support?

a.

four

b.

three

c.

two

d.

one

____ 25. What
is a full-floating axle?

a.

an axle that supports none of the vehicle weight

b.

an axle that supports the full vehicle weight and
drives the wheels

c.

an axle that supports some of the vehicle weight

d.

an axle that supports the full vehicle weight

____ 26. The
vehicle produces a noise that remains constant while accelerating,
decelerating, or coasting at 50 km/h (30 mph). Which of the following parts is
likely generating the noise?

a.

tires

b.

pinion bearing

c.

ring and pinion gear

d.

side gears

___ 28. How
fast will a vehicle accelerate if the two driven wheels have unequal traction?

a.

at a rate equal to the wheel with the least traction

b.

at a rate equal to the crown gear

c.

at a rate equal to the average of the two wheels

d.

at a rate equal to the wheel with the most traction

____ 29. In
a limited-slip differential, the friction disks are located between which
parts?

a.

the two side gears

b.

the side gears and the case

c.

the side gears and the carrier

d.

the ring and the pinion

16. Which of the following may be reused when
rebuilding a transmission?

a.

seals

b.

synchronizer assemblies

c.

snap rings

d.

gaskets

18. How long should you wait before checking the gear lubricant level
if the engine has been running?

a.

3 minutes

b.

5 minutes

c.

30 minutes

d.

10 minutes

19. Technician A says broken or worn engine
and transaxle mounts can cause a transaxle to have shifting problems. Technician
B says poor shift boot alignment cannot cause a transaxle to jump out of
gear. Who is correct?

a.

B only

b.

A only

c.

neither A nor B

d.

both A and B

21. What is the first step in rear oil seal and
bushing replacement?

a.

index and remove the driveshaft

b.

check for leaks

c.

clean the driveshaft

d.

drain fluid

23. Which faulty part would be likely to cause a
car to jump out of gear into neutral when decelerating or going down hills?

a.

counter shaft bearings

b.

chipped speed gears

c.

synchronizer blocker ring

_0d.

internal gearshift linkage

26. Which of the following may need to be adjusted
after the transmission has been disassembled??

a.

roller bearings

b.

CV joints

c.

shift fork

d.

shift lever

. Which of the following gear ratios shows an
overdrive condition?

a.

2.15:1

b.

0.85:1

c.

1:1

d.

10:1

11. Which of the following terms is used to
describe the number of gear teeth per unit of measurement around the gear’s
diameter?

a.

size

b.

load

c.

pitch

d.

ratio

16. What component is used to lock the main shaft
(output shaft) and a speed gear together?

a.

shift linkage

b.

transfer case

c.

synchronizer

d.

shift fork

18. Which of the following gear ratios generates
the highest torque or power output?

a.

5.23:1

b.

11.12:1

c.

0.85:1

d.

2.67:1

12. Which of the following controls the engagement and disengagement
of the clutch assembly?

a.

pressure plate assembly

b.

clutch linkage

c.

clutch pedal

d.

clutch release bearing

With
which component does the clutch friction disc always rotate?

a.

transmission input shaft

b.

engine crankshaft

c.

pressure plate

d.

flywheel

3. Which of the following is a likely cause of a
vibrating clutch?

a.

loose flywheel bolts

b.

weak clutch springs

c.

excessive crankshaft endplay

d.

oil on the clutch disk

5. Where does the power flow stop when the clutch
is disengaged?

a.

at the torsion springs

b.

at the driven disc hub

c.

at the transmission input shaft

d.

at the pressure plate and flywheel

18. Which of the following types of springs are used
to provide application pressure in pressure plate assemblies?

a.

diaphragm

b.

torsional

c.

Belleville

d.

coil

21. Which of the following would likely be the result of loose bell
housing bolts?

a.

high pedal effort

b.

noisy engagement

c.

chatter

d.

slippage

What is the most likely cause of whirring or
grating noise that disappears when the clutch pedal is being depressed and
stops when the pedal is fully released?

a.

crankshaft main bearing

b.

input shaft bearing

c.

release bearing

d.

pilot bearing

25. Which of the following would likely result from too little clutch
pedal free play?

a.

premature release bearing failure

b.

clutch slippage

c.

clutch chatter

d.

gear clash

27. Which of the following is the main factor in
determining the service life of a clutch?

a.

good driving habits

b.

brand of clutch

c.

size of engine

d.

disc-facing material

____ 28. Which
of the following would likely cause clutch chatter or grabbing while engaging?

a.

weak springs in the pressure plate

b.

high engine idle speed

c.

releasing the clutch pedal too slowly

d.

oil or grease on the friction disk

We offer CUSTOM-WRITTEN, CONFIDENTIAL, ORIGINAL, and PRIVATE writing services. Kindly click on the ORDER NOW button to receive an A++ paper from our masters- and PhD writers.

Get a 10% discount on your order using the following coupon code SAVE10


Order a Similar Paper Order a Different Paper